BH93420 submersible transmitter , use HT series piezoresistive silicon oil-filled sensor as measurement component. According the relation between pressure, density and liquid level, the hydraulic transducers measure the liquid pressure which in direct ratio with depth of liquid, then via amplificatory circuit, the measured pressure is transferred to standard signal. Special use cable, advanced seal technology, reliable amplify circuit and accurate compensation technic ensure the products have high accuracy and good capability of anti-leakage.
Compatible with 316LSS,noncorrosive liquids
Apply in Petroleum industry, chemical industry, generating station, water supply, hydrology etc. those need to measure
&control liquid`s level.
≤1.5X rated range
Long term stability
±0.2%F.S/year (＞20mH2O) ±20mm(≤20mH2O)
Operating temperature range
4~20mA 0~10/20mA 0/1~5/10VDC
304 stainless steel
Polyethylene ventilate cable
Signal wire do not through the metal tube or put in the same wire groove with other power line,also do not in the vicinity of high-voltage devices.
Signal line may be floating or ground at any point in the signal loop .Transmitter housing may be grounded or ungrounded.
The transmitter coupled to ground through a capacitor, so when check the insulation resistance, can not use megger which higher than 100V , check the circuit should not be higher than 45V.
Submersible transmitter installation notes
1). Fix bracket in the proper position, meet the requirements of the mounting height.
2). According to the wiring diagram to connect wire
3). The load resistance discrepancy can be adjusted according to user needs.
4). The sensor probe must be put into the fluid vertically, not skewed, to prevent errors .
1). Please connect the wire with the following diagram. If reversed, because the transmitter internal use protective measures, there will be no output.
The transmitter power can work, but warm up for 30 minutes then the output signal is more stable and reliable.
2). The maximum pressure of the system must not exceed the rated value of the overload. Back pressure side of the transmitter can not be connected directly to the conductive, corrosive liquids or gases.
3). The product is precision measuring instruments, forbidden to break at random, clamping strongly , demolition.
4). The instrument installed in ventilated, dry and free of corrosion, shady place as far as possible. If working in harsh environment, should take appropriate measures to protect the instrument.
5). The output abnormal, stop to check, if the case of product quality problems return along with factory repair or replacement warranty card and instruction manual.
6). Non-specialized person do not disassemble the instrument board, or change other devices.
7). This is a four core cable(red, yellow,blue,green), as shown in the wiring diagram, only red, yellow,shielding wire is available.The blue and green wires are used to calibrate, they can`t touch red and yellow wire when power on , to avoid damage of circuit board .if user need to change cable length, it is best to protect blue and green wire with heat shrinkable tube.
Baoji Hengtong Electronics Co.,Ltd was founded in 1994. 80 million of assets, occupying over 7000 square meter factory, 1261 sets of equipment and instruments,with more than 100 workers. It is scientific research, production, management, engineering design, installation and debugging and related services for the integration of enterprises. We are specialized in manufacture of pressure, differential pressure, absolute pressure, liquid pressure, temperature transducers and transmitters and the relative smart numeral display controllers. These products have been widely used in automatic measuring and controlling system in fields of chemical, metallurgy, electricity, aero-industry, coal and petroleum exploitation, irrigation and hydrology, communication and water supply, steam supply, warm supply of town. Some of the products are used in major national projects, and spoke highly of the relevant state departments.Our HT-series oil-filled sensors with membrane are produced by advanced technology, with features of reliable performance, high precision. Many products have been exported to Europe, America, Asia and other regions and countries.
Our products information as below:
6. BPK series pressure controller
7. Customized products according to customer requirement.
Baoji Hengtong Electronics Co.,Ltd
No.195 Gaoxin Road, Baoji City, Shaanxi province,China
Mob/skype/wechat:+86 152 4907 2699
Looking for ideal Submersible 4-20mA Pressure Level Transmitter
Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Submersible Water Level Transmitter are quality guaranteed. We are China Origin Factory of Submersible Liquid Level Transmitter. If you have any question, please feel free to contact us.
Product Categories : Liquid Level Transmitter > Silicon Oil-filled Liquid Level Transmitter